-
1 inspection and verification means
Военный термин: (технические) средства инспекции и контроля (соблюдения соглашения)Универсальный англо-русский словарь > inspection and verification means
-
2 inspection and verification means
( технические) средства инспекции и контроля ( соблюдения соглашения)English-Russian military dictionary > inspection and verification means
-
3 means
-
4 assembly manufacturer
изготовитель НКУ
Организация, которая выполнила разработку конструкции, изготовление и необходимую проверку на соответствие НКУ требованиям конкретного стандарта.
[ ГОСТ Р МЭК 61439-1-2013]EN
original manufacturer
organization that has carried out the original design and the associated verification of an assembly in accordance with the relevant assembly standard
[IEC 61439-1, ed. 2.0 (2011-08)]FR
constructeur d'origine
organisme qui a réalisé la conception d'origine et la vérification associée d’un ensemble conformément à la norme d’ensembles applicable
[IEC 61439-1, ed. 2.0 (2011-08)]Параллельные тексты EN-RU
6.1 ASSEMBLY designation marking
The ASSEMBLY manufacturer shall provide each ASSEMBLY with one or more labels, marked in a durable manner and located in a place such that they are visible and legible when the ASSEMBLY is installed and in operation.
Compliance is checked according to the test of 10.2.7 and by inspection.
The following information regarding the ASSEMBLY shall be provided on the designation label(s):
a) ASSEMBLY manufacturer's name or trade mark (see 3.10.2);
b) type designation or identification number or any other means of identification, making it possible to obtain relevant information from the ASSEMBLY manufacturer;
c) means of identifying date of manufacture;
d) IEC 61439-X (the specific part “X” shall be identified).
NOTE The relevant ASSEMBLY standard may specify where additional information is to be provided on the designation label.
[BS EN 61439-1:2009]6.1 Маркировка
Изготовитель НКУ должен предусмотреть на каждом НКУ одну или несколько табличек со стойкой к внешним воздействиям маркировкой, которые после установки и в процессе эксплуатации НКУ должны быть расположены на видном месте.
Соответствие проверяют испытанием по 10.2.7 и внешним осмотром.
На паспортной табличке должна быть приведена информация об НКУ, указанная в перечислениях а) — d):
a) наименование изготовителя или его товарный знак (см. 3.10.2):
b) обозначение типа, идентификационный или другой знак, позволяющий получить необходимую информацию от изготовителя;
c) обозначение даты изготовления;
d) обозначение настоящего стандарта.
Примечание — На паспортной табличке может быть приведено обозначение конкретного стандарта на НКУ, если требуется дополнительная информация.
[ ГОСТ Р МЭК 61439.1-2013]
Тематики
- НКУ (шкафы, пульты,...)
Синонимы
EN
- assembly manufacturer
- ASSEMBLY manufacturer
- original equipment manufacturer
- original manufacturer
- panel builder
- panel-builder
- switchboard manufacturer
FR
изготовитель НКУ
Организация, которая выполнила разработку конструкции, изготовление и необходимую проверку на соответствие НКУ требованиям конкретного стандарта.
[ ГОСТ Р МЭК 61439-1-2013]EN
original manufacturer
organization that has carried out the original design and the associated verification of an assembly in accordance with the relevant assembly standard
[IEC 61439-1, ed. 2.0 (2011-08)]FR
constructeur d'origine
organisme qui a réalisé la conception d'origine et la vérification associée d’un ensemble conformément à la norme d’ensembles applicable
[IEC 61439-1, ed. 2.0 (2011-08)]Параллельные тексты EN-RU
6.1 ASSEMBLY designation marking
The ASSEMBLY manufacturer shall provide each ASSEMBLY with one or more labels, marked in a durable manner and located in a place such that they are visible and legible when the ASSEMBLY is installed and in operation.
Compliance is checked according to the test of 10.2.7 and by inspection.
The following information regarding the ASSEMBLY shall be provided on the designation label(s):
a) ASSEMBLY manufacturer's name or trade mark (see 3.10.2);
b) type designation or identification number or any other means of identification, making it possible to obtain relevant information from the ASSEMBLY manufacturer;
c) means of identifying date of manufacture;
d) IEC 61439-X (the specific part “X” shall be identified).
NOTE The relevant ASSEMBLY standard may specify where additional information is to be provided on the designation label.
[BS EN 61439-1:2009]6.1 Маркировка
Изготовитель НКУ должен предусмотреть на каждом НКУ одну или несколько табличек со стойкой к внешним воздействиям маркировкой, которые после установки и в процессе эксплуатации НКУ должны быть расположены на видном месте.
Соответствие проверяют испытанием по 10.2.7 и внешним осмотром.
На паспортной табличке должна быть приведена информация об НКУ, указанная в перечислениях а) — d):
a) наименование изготовителя или его товарный знак (см. 3.10.2):
b) обозначение типа, идентификационный или другой знак, позволяющий получить необходимую информацию от изготовителя;
c) обозначение даты изготовления;
d) обозначение настоящего стандарта.
Примечание — На паспортной табличке может быть приведено обозначение конкретного стандарта на НКУ, если требуется дополнительная информация.
[ ГОСТ Р МЭК 61439.1-2013]
Тематики
- НКУ (шкафы, пульты,...)
Синонимы
EN
- assembly manufacturer
- ASSEMBLY manufacturer
- original equipment manufacturer
- original manufacturer
- panel builder
- panel-builder
- switchboard manufacturer
FR
сборщик НКУ
Организация, ответственная за сборку НКУ.
Примечание. Разработчик и сборщик НКУ могут быть разными организациями.
[ ГОСТ Р МЭК 61439-1-2012]EN
assembly manufacturer
organization taking the responsibility for the completed assembly
NOTE The assembly manufacturer may be a different organisation to the original manufacturer.
[IEC 61439-1, ed. 2.0 (2011-08)]FR
constructeur d’ensembles
organisme prenant la responsabilité de l’ensemble fini
NOTE Le constructeur d’ensembles peut être un organisme différent du constructeur d'origine.
[IEC 61439-1, ed. 2.0 (2011-08)]Тематики
- НКУ (шкафы, пульты,...)
EN
FR
- constructeur d’ensembles
Англо-русский словарь нормативно-технической терминологии > assembly manufacturer
-
5 original manufacturer
изготовитель НКУ
Организация, которая выполнила разработку конструкции, изготовление и необходимую проверку на соответствие НКУ требованиям конкретного стандарта.
[ ГОСТ Р МЭК 61439-1-2013]EN
original manufacturer
organization that has carried out the original design and the associated verification of an assembly in accordance with the relevant assembly standard
[IEC 61439-1, ed. 2.0 (2011-08)]FR
constructeur d'origine
organisme qui a réalisé la conception d'origine et la vérification associée d’un ensemble conformément à la norme d’ensembles applicable
[IEC 61439-1, ed. 2.0 (2011-08)]Параллельные тексты EN-RU
6.1 ASSEMBLY designation marking
The ASSEMBLY manufacturer shall provide each ASSEMBLY with one or more labels, marked in a durable manner and located in a place such that they are visible and legible when the ASSEMBLY is installed and in operation.
Compliance is checked according to the test of 10.2.7 and by inspection.
The following information regarding the ASSEMBLY shall be provided on the designation label(s):
a) ASSEMBLY manufacturer's name or trade mark (see 3.10.2);
b) type designation or identification number or any other means of identification, making it possible to obtain relevant information from the ASSEMBLY manufacturer;
c) means of identifying date of manufacture;
d) IEC 61439-X (the specific part “X” shall be identified).
NOTE The relevant ASSEMBLY standard may specify where additional information is to be provided on the designation label.
[BS EN 61439-1:2009]6.1 Маркировка
Изготовитель НКУ должен предусмотреть на каждом НКУ одну или несколько табличек со стойкой к внешним воздействиям маркировкой, которые после установки и в процессе эксплуатации НКУ должны быть расположены на видном месте.
Соответствие проверяют испытанием по 10.2.7 и внешним осмотром.
На паспортной табличке должна быть приведена информация об НКУ, указанная в перечислениях а) — d):
a) наименование изготовителя или его товарный знак (см. 3.10.2):
b) обозначение типа, идентификационный или другой знак, позволяющий получить необходимую информацию от изготовителя;
c) обозначение даты изготовления;
d) обозначение настоящего стандарта.
Примечание — На паспортной табличке может быть приведено обозначение конкретного стандарта на НКУ, если требуется дополнительная информация.
[ ГОСТ Р МЭК 61439.1-2013]
Тематики
- НКУ (шкафы, пульты,...)
Синонимы
EN
- assembly manufacturer
- ASSEMBLY manufacturer
- original equipment manufacturer
- original manufacturer
- panel builder
- panel-builder
- switchboard manufacturer
FR
разработчик НКУ
-
[Интент]
разработчик НКУ
Организация, которая выполнила разработку конструкции и необходимую проверку на соответствие НКУ требованиям конкретного стандарта.
[ ГОСТ Р МЭК 61439.1-2012]EN
original manufacturer
organization that has carried out the original design and the associated verification of an assembly in accordance with the relevant assembly standard
[IEC 61439-1, ed. 2.0 (2011-08)]FR
constructeur d'origine
organisme qui a réalisé la conception d'origine et la vérification associée d’un ensemble conformément à la norme d’ensembles applicable
[IEC 61439-1, ed. 2.0 (2011-08)]Тематики
- НКУ (шкафы, пульты,...)
EN
FR
Англо-русский словарь нормативно-технической терминологии > original manufacturer
-
6 panel builder
изготовитель НКУ
Организация, которая выполнила разработку конструкции, изготовление и необходимую проверку на соответствие НКУ требованиям конкретного стандарта.
[ ГОСТ Р МЭК 61439-1-2013]EN
original manufacturer
organization that has carried out the original design and the associated verification of an assembly in accordance with the relevant assembly standard
[IEC 61439-1, ed. 2.0 (2011-08)]FR
constructeur d'origine
organisme qui a réalisé la conception d'origine et la vérification associée d’un ensemble conformément à la norme d’ensembles applicable
[IEC 61439-1, ed. 2.0 (2011-08)]Параллельные тексты EN-RU
6.1 ASSEMBLY designation marking
The ASSEMBLY manufacturer shall provide each ASSEMBLY with one or more labels, marked in a durable manner and located in a place such that they are visible and legible when the ASSEMBLY is installed and in operation.
Compliance is checked according to the test of 10.2.7 and by inspection.
The following information regarding the ASSEMBLY shall be provided on the designation label(s):
a) ASSEMBLY manufacturer's name or trade mark (see 3.10.2);
b) type designation or identification number or any other means of identification, making it possible to obtain relevant information from the ASSEMBLY manufacturer;
c) means of identifying date of manufacture;
d) IEC 61439-X (the specific part “X” shall be identified).
NOTE The relevant ASSEMBLY standard may specify where additional information is to be provided on the designation label.
[BS EN 61439-1:2009]6.1 Маркировка
Изготовитель НКУ должен предусмотреть на каждом НКУ одну или несколько табличек со стойкой к внешним воздействиям маркировкой, которые после установки и в процессе эксплуатации НКУ должны быть расположены на видном месте.
Соответствие проверяют испытанием по 10.2.7 и внешним осмотром.
На паспортной табличке должна быть приведена информация об НКУ, указанная в перечислениях а) — d):
a) наименование изготовителя или его товарный знак (см. 3.10.2):
b) обозначение типа, идентификационный или другой знак, позволяющий получить необходимую информацию от изготовителя;
c) обозначение даты изготовления;
d) обозначение настоящего стандарта.
Примечание — На паспортной табличке может быть приведено обозначение конкретного стандарта на НКУ, если требуется дополнительная информация.
[ ГОСТ Р МЭК 61439.1-2013]
Тематики
- НКУ (шкафы, пульты,...)
Синонимы
EN
- assembly manufacturer
- ASSEMBLY manufacturer
- original equipment manufacturer
- original manufacturer
- panel builder
- panel-builder
- switchboard manufacturer
FR
разработчик НКУ
-
[Интент]
разработчик НКУ
Организация, которая выполнила разработку конструкции и необходимую проверку на соответствие НКУ требованиям конкретного стандарта.
[ ГОСТ Р МЭК 61439.1-2012]EN
original manufacturer
organization that has carried out the original design and the associated verification of an assembly in accordance with the relevant assembly standard
[IEC 61439-1, ed. 2.0 (2011-08)]FR
constructeur d'origine
organisme qui a réalisé la conception d'origine et la vérification associée d’un ensemble conformément à la norme d’ensembles applicable
[IEC 61439-1, ed. 2.0 (2011-08)]Тематики
- НКУ (шкафы, пульты,...)
EN
FR
Англо-русский словарь нормативно-технической терминологии > panel builder
-
7 original equipment manufacturer
изготовитель НКУ
Организация, которая выполнила разработку конструкции, изготовление и необходимую проверку на соответствие НКУ требованиям конкретного стандарта.
[ ГОСТ Р МЭК 61439-1-2013]EN
original manufacturer
organization that has carried out the original design and the associated verification of an assembly in accordance with the relevant assembly standard
[IEC 61439-1, ed. 2.0 (2011-08)]FR
constructeur d'origine
organisme qui a réalisé la conception d'origine et la vérification associée d’un ensemble conformément à la norme d’ensembles applicable
[IEC 61439-1, ed. 2.0 (2011-08)]Параллельные тексты EN-RU
6.1 ASSEMBLY designation marking
The ASSEMBLY manufacturer shall provide each ASSEMBLY with one or more labels, marked in a durable manner and located in a place such that they are visible and legible when the ASSEMBLY is installed and in operation.
Compliance is checked according to the test of 10.2.7 and by inspection.
The following information regarding the ASSEMBLY shall be provided on the designation label(s):
a) ASSEMBLY manufacturer's name or trade mark (see 3.10.2);
b) type designation or identification number or any other means of identification, making it possible to obtain relevant information from the ASSEMBLY manufacturer;
c) means of identifying date of manufacture;
d) IEC 61439-X (the specific part “X” shall be identified).
NOTE The relevant ASSEMBLY standard may specify where additional information is to be provided on the designation label.
[BS EN 61439-1:2009]6.1 Маркировка
Изготовитель НКУ должен предусмотреть на каждом НКУ одну или несколько табличек со стойкой к внешним воздействиям маркировкой, которые после установки и в процессе эксплуатации НКУ должны быть расположены на видном месте.
Соответствие проверяют испытанием по 10.2.7 и внешним осмотром.
На паспортной табличке должна быть приведена информация об НКУ, указанная в перечислениях а) — d):
a) наименование изготовителя или его товарный знак (см. 3.10.2):
b) обозначение типа, идентификационный или другой знак, позволяющий получить необходимую информацию от изготовителя;
c) обозначение даты изготовления;
d) обозначение настоящего стандарта.
Примечание — На паспортной табличке может быть приведено обозначение конкретного стандарта на НКУ, если требуется дополнительная информация.
[ ГОСТ Р МЭК 61439.1-2013]
Тематики
- НКУ (шкафы, пульты,...)
Синонимы
EN
- assembly manufacturer
- ASSEMBLY manufacturer
- original equipment manufacturer
- original manufacturer
- panel builder
- panel-builder
- switchboard manufacturer
FR
изготовитель оборудования
Обозначение компаний, производящих оборудование, которое впоследствии выпускается на рынок и продается другим фирмам под их собственными названиями.
[ http://www.alltso.ru/publ/glossarij_setevoe_videonabljudenie_terminy/1-1-0-34]EN
производитель комплектного оборудования
Компания, приобретающая комплектующие изделия одного или нескольких изготовителей и после комплексной сборки (иногда с незначительной доработкой) выпускающая готовую продукцию под своей маркой. Доработка в основном связана с введением вспомогательных аппаратных и программных средств, необходимых для тестирования и отладки OEM-оборудования, а также реализации новых возможностей, обеспечиваемых по заказу потребителя.
[Л.М. Невдяев. Телекоммуникационные технологии. Англо-русский толковый словарь-справочник. Под редакцией Ю.М. Горностаева. Москва, 2002]Тематики
- электросвязь, основные понятия
EN
Англо-русский словарь нормативно-технической терминологии > original equipment manufacturer
-
8 panel-builder
изготовитель НКУ
Организация, которая выполнила разработку конструкции, изготовление и необходимую проверку на соответствие НКУ требованиям конкретного стандарта.
[ ГОСТ Р МЭК 61439-1-2013]EN
original manufacturer
organization that has carried out the original design and the associated verification of an assembly in accordance with the relevant assembly standard
[IEC 61439-1, ed. 2.0 (2011-08)]FR
constructeur d'origine
organisme qui a réalisé la conception d'origine et la vérification associée d’un ensemble conformément à la norme d’ensembles applicable
[IEC 61439-1, ed. 2.0 (2011-08)]Параллельные тексты EN-RU
6.1 ASSEMBLY designation marking
The ASSEMBLY manufacturer shall provide each ASSEMBLY with one or more labels, marked in a durable manner and located in a place such that they are visible and legible when the ASSEMBLY is installed and in operation.
Compliance is checked according to the test of 10.2.7 and by inspection.
The following information regarding the ASSEMBLY shall be provided on the designation label(s):
a) ASSEMBLY manufacturer's name or trade mark (see 3.10.2);
b) type designation or identification number or any other means of identification, making it possible to obtain relevant information from the ASSEMBLY manufacturer;
c) means of identifying date of manufacture;
d) IEC 61439-X (the specific part “X” shall be identified).
NOTE The relevant ASSEMBLY standard may specify where additional information is to be provided on the designation label.
[BS EN 61439-1:2009]6.1 Маркировка
Изготовитель НКУ должен предусмотреть на каждом НКУ одну или несколько табличек со стойкой к внешним воздействиям маркировкой, которые после установки и в процессе эксплуатации НКУ должны быть расположены на видном месте.
Соответствие проверяют испытанием по 10.2.7 и внешним осмотром.
На паспортной табличке должна быть приведена информация об НКУ, указанная в перечислениях а) — d):
a) наименование изготовителя или его товарный знак (см. 3.10.2):
b) обозначение типа, идентификационный или другой знак, позволяющий получить необходимую информацию от изготовителя;
c) обозначение даты изготовления;
d) обозначение настоящего стандарта.
Примечание — На паспортной табличке может быть приведено обозначение конкретного стандарта на НКУ, если требуется дополнительная информация.
[ ГОСТ Р МЭК 61439.1-2013]
Тематики
- НКУ (шкафы, пульты,...)
Синонимы
EN
- assembly manufacturer
- ASSEMBLY manufacturer
- original equipment manufacturer
- original manufacturer
- panel builder
- panel-builder
- switchboard manufacturer
FR
Англо-русский словарь нормативно-технической терминологии > panel-builder
-
9 switchboard manufacturer
изготовитель НКУ
Организация, которая выполнила разработку конструкции, изготовление и необходимую проверку на соответствие НКУ требованиям конкретного стандарта.
[ ГОСТ Р МЭК 61439-1-2013]EN
original manufacturer
organization that has carried out the original design and the associated verification of an assembly in accordance with the relevant assembly standard
[IEC 61439-1, ed. 2.0 (2011-08)]FR
constructeur d'origine
organisme qui a réalisé la conception d'origine et la vérification associée d’un ensemble conformément à la norme d’ensembles applicable
[IEC 61439-1, ed. 2.0 (2011-08)]Параллельные тексты EN-RU
6.1 ASSEMBLY designation marking
The ASSEMBLY manufacturer shall provide each ASSEMBLY with one or more labels, marked in a durable manner and located in a place such that they are visible and legible when the ASSEMBLY is installed and in operation.
Compliance is checked according to the test of 10.2.7 and by inspection.
The following information regarding the ASSEMBLY shall be provided on the designation label(s):
a) ASSEMBLY manufacturer's name or trade mark (see 3.10.2);
b) type designation or identification number or any other means of identification, making it possible to obtain relevant information from the ASSEMBLY manufacturer;
c) means of identifying date of manufacture;
d) IEC 61439-X (the specific part “X” shall be identified).
NOTE The relevant ASSEMBLY standard may specify where additional information is to be provided on the designation label.
[BS EN 61439-1:2009]6.1 Маркировка
Изготовитель НКУ должен предусмотреть на каждом НКУ одну или несколько табличек со стойкой к внешним воздействиям маркировкой, которые после установки и в процессе эксплуатации НКУ должны быть расположены на видном месте.
Соответствие проверяют испытанием по 10.2.7 и внешним осмотром.
На паспортной табличке должна быть приведена информация об НКУ, указанная в перечислениях а) — d):
a) наименование изготовителя или его товарный знак (см. 3.10.2):
b) обозначение типа, идентификационный или другой знак, позволяющий получить необходимую информацию от изготовителя;
c) обозначение даты изготовления;
d) обозначение настоящего стандарта.
Примечание — На паспортной табличке может быть приведено обозначение конкретного стандарта на НКУ, если требуется дополнительная информация.
[ ГОСТ Р МЭК 61439.1-2013]
Тематики
- НКУ (шкафы, пульты,...)
Синонимы
EN
- assembly manufacturer
- ASSEMBLY manufacturer
- original equipment manufacturer
- original manufacturer
- panel builder
- panel-builder
- switchboard manufacturer
FR
Англо-русский словарь нормативно-технической терминологии > switchboard manufacturer
-
10 method
метод; процедура; способ- antithetic variate method - average ordinate method - average range method - binary search method - conjugate directions method - conjugate gradient method - control chart method - conventional milling method - correlation function method - decision function method - differential control method - Feynman diagram method - first approximation method - gradient projection method - iterative method - large sample method - large sieve method - least-squares regression method - less than fully efficient method - linearly implicit method - method of adjoint gradient - method of algebraic addition - method of alternating directions - method of balanced blocks - method of complex numbers - method of confidence intervals - method of conformal mappings - method of conjugate directions - method of conjugate gradients - method of cyclic descent - method of detached coefficients - method of disjunction of cases - method of divided differences - method of electrical images - method of elimination of quantifiers - method of empty ball - method of extreme values - method of false position - method of feasible directions - method of finite differences - method of first approximation - method of first entrance - method of fitting constants - method of fixed points - method of full enumeration - method of generating functions - method of geometric exhaustion - method of indefinite coefficients - method of infinite descent - method of interval bisection - method of least absolute values - method of least distance - method of least likelihood - method of maximum likelihood - method of means and standard deviations - method of medians and extreme values - method of minimal change - method of minimal variance - method of mirror reflections - method of moving frame - method of multiple comparison - method of orthogonal projections - method of paired associates - method of paired comparisons - method of phase integrals - method of projecting cones - method of proportional parts - method of rotating factors - method of semantic tableaux - method of separation of variables - method of simulaneous displacements - method of stationary phase - method of statistical differentials - method of statistical inference - method of steep variations - method of steepest ascent - method of stochastic approximation - method of straightforward iteration - method of successive displacements - method of successive divisions - method of successive elimination - method of transfinite induction - method of unweighted means - method of variable differences - method of variation of parameters - method of weighted residuals - optimum method - parallel tangents method - precision method - random walk method - recursive method - reduced gradient method - reflected wave method - relative method of measurement - sampling method by variables - statistical sampling method - steepest descent method - time average method -
11 test
1) тест, испытание, испытания; проверка || испытывать, проводить испытания; проверять2) показатель; стат. критерий, признак- odd test
См. также в других словарях:
Device driver synthesis and verification — The device driver is a program which allows the software or higher level computer programs to interact with a hardware device. These software components act as a link between the devices and the operating systems, communicating with each of these … Wikipedia
Anthropology and Archaeology — ▪ 2009 Introduction Anthropology Among the key developments in 2008 in the field of physical anthropology was the discovery by a large interdisciplinary team of Spanish and American scientists in northern Spain of a partial mandible (lower… … Universalium
Commercial Vessel Inspection (USCG) — In the United States, the Coast Guard (USCG) is responsible for inspecting vessels (i.e. boat or ship) in Federal waters.The Coast Guard delegates this responsibility to the Officer in Charge Marine InspectionsInspections are done either under… … Wikipedia
Writ of Amparo and Habeas Data (Philippines) — See also: amparo (law). The Writ of Amparo and Habeas Data (Philippines) are Prerogative writs to supplement the inefficacy of Philippine Habeas Corpus (Rule 102, Revised Rules of Court). Amparo means protection, while Habeas Data is access to… … Wikipedia
Illegal, unreported and unregulated fishing — Illegal fishing takes place where vessels operate in violation of the laws of a fishery. This can apply to fisheries that are under the jurisdiction of a coastal state or to high seas fisheries regulated by regional organisations. Unreported… … Wikipedia
Packaging and labelling — Packaging is the science, art and technology of enclosing or protecting products for distribution, storage, sale, and use. Packaging also refers to the process of design, evaluation, and production of packages. Package labelling (BrE) or labeling … Wikipedia
National technical means of verification — is a phrase that first appeared, but was not detailed, in the Strategic Arms Limitation Treaty (SALT) between the US and USSR. At first, the phrase reflected a concern that the Soviet Union could be particularly disturbed by public recognition of … Wikipedia
Hazard Analysis and Critical Control Points — (HACCP) is a systematic preventive approach to food safety and pharmaceutical safety that addresses physical, chemical, and biological hazards as a means of prevention rather than finished product inspection. HACCP is used in the food industry to … Wikipedia
Iran and weapons of mass destruction — This article is about Iran and weapons of mass destruction. For Iran s nuclear power program, see Nuclear program of Iran. Weapons of mass destruction … Wikipedia
Health and Disease — ▪ 2009 Introduction Food and Drug Safety. In 2008 the contamination of infant formula and related dairy products with melamine in China led to widespread health problems in children, including urinary problems and possible renal tube… … Universalium
Law, Crime, and Law Enforcement — ▪ 2006 Introduction Trials of former heads of state, U.S. Supreme Court rulings on eminent domain and the death penalty, and high profile cases against former executives of large corporations were leading legal and criminal issues in 2005.… … Universalium